Eicon Networks DIVA T/A ISDN Modem Betriebsanweisung Seite 89
- Seite / 191
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter Seven: Setting up the Phone Ports Supplementary services
89
Notes on Call Waiting behavior
The following situations apply if you are on the phone and a second call comes in:
Notes on call bumping
If ISDN Call Waiting is disabled, call bumping will not occur, as MultiLink PPP uses the Call Waiting
signalling information from your service provider to determine if it should release a B-channel to
accommodate an incoming voice call.
Calling Line Identity on Call Waiting
Calling Line Identity on Call Waiting works with telephones equipped with a call display indicator. With this
feature, if you are on the phone and another call comes in, the number of the second incoming call is displayed.
In Denmark, this feature is known as CallerID Plus. CallerID Plus does not display the identity of the second
call automatically; when you receive a call waiting signal, you must press R, then 9.
Calling Line Identity Presentation
Calling Line Identity Presentation works with telephones equipped with a call display indicator. When you
receive an incoming call, the number of the call is displayed.
Calling Line Identity Restriction (CLIR)
This feature permits you to restrict calling line identity on outgoing calls on a per-call basis. Currently this
feature is supported on the phone ports only.
To restrict identification on a per-call basis, you must enter a code before dialing the number. This code
depends on your region.
Denmark
1.
Lift the receiver.
2.
Dial *31# followed by the number you wish to call.
If you have CLIR permanently enabled on your line, you can temporarily disable it using the prefix #31#.
United Kingdom and Ireland
In these regions, you must dial 141 before dialing the destination number. For example, if you were calling
5551234, you would dial 1415551234.
If ... Then ...
• ISDN Call Waiting is enabled. • You will hear a Call Waiting alert.
• Call switching is handled by your ISDN service
provider.
• ISDN Call Waiting is not enabled.
• DIVA LAN ISDN Modem Call Waiting
is not enabled.
• You do not receive a Call Waiting alert.
• The second call receives a busy signal.
• ISDN Call Waiting is not enabled.
• DIVA LAN ISDN Modem Call Waiting
is enabled.
• Both B-channels are in use.
• The second call receives a busy signal., as the
DIVA LAN ISDN Modem Call Waiting requires
a free B-channel to hold the call.
• ISDN Call Waiting is not enabled.
• DIVA LAN ISDN Modem Call Waiting
is enabled.
• One B-channel is free.
• You hear a Call Waiting alert.
• The second call is received using the available
B-channel.
• Call switching is handled by the DIVA LAN
ISDN Modem.
- DIVA LAN ISDN Modem 1
- User’s Guide 1
- Table of Contents 3
- Chapter Three: 4
- Chapter Four: 4
- Chapter Five: 4
- Chapter Six: 5
- Chapter Seven: 5
- Chapter Eight: 6
- Chapter Nine: 6
- Chapter Ten: 6
- Appendix A: 7
- Appendix B: 7
- Appendix C: 7
- Appendix D: 8
- Introduction 9
- Internet 10
- Connecting more computers 12
- Total network security 12
- Summary of features 13
- Contacting customer services 14
- Getting Started 15
- 1. Installation overview 16
- 2. Prepare for installation 17
- Important ISDN concepts 19
- ISDN channel usage 19
- Multilink PPP 20
- Multilink PPP + BACP 20
- Multilink PPP + AO/DI 20
- Gather ISDN information 22
- Gather X.25 information 23
- Gather V.120 information 23
- Power Supply 24
- FaxPhone 24
- ISDN Wall Outlet 24
- To install Modem Monitor 26
- What’s next? 34
- Starting Modem Monitor 36
- Properties dialog box 37
- Utilities dialog box 38
- Options dialog box 38
- Status Viewer 39
- Profile table 40
- Utilities 40
- Chapter Four 41
- Saving configuration settings 43
- Getting help 43
- General settings 43
- Connection profile settings 43
- Editing the ISP profile 44
- Editing LAN settings 45
- Viewing status information 46
- Obtaining statistics 47
- Eicon\DIVA LAN ISDN Modem\ELM 48
- Resetting to factory defaults 49
- Minimizing ISDN Charges 50
- The Cost Control page 51
- Data call thresholds 52
- ISDN billing intervals 52
- Configuring BACP 53
- Configuring AO/DI 54
- X.25 on the D-channel 56
- Click Save 57
- Click Reset 57
- Setting ISDN active intervals 58
- Spoofing NetBIOS services 59
- Data compression 60
- Manual dialing 61
- Restricting analog calls 62
- Data over voice 63
- Traffic filtering 64
- Security 65
- Security features 66
- System password 67
- Automatic log out 67
- Network address translation 68
- Remote management 70
- Incoming data calls 72
- Call authentication 74
- Custom security features 78
- Setting up the Phone Ports 79
- Assigning phone numbers 80
- Call bumping 84
- Supplementary services 86
- Call Hold 87
- Call Waiting 87
- Notes on call bumping 89
- Call Forwarding 90
- Three-party Conference Call 91
- Terminal Portability 92
- Chapter Eight 93
- Overview 94
- 1. Gather information 95
- Minimizing your ISDN charges 100
- Configuring security features 101
- Advanced Installations 102
- Connection retries 103
- Using Modem Monitor 104
- Manual installation 105
- 106 106
- To create a VPN 108
- Connecting to the VPN 109
- Defining routes 110
- IP routes 111
- 117 117
- 118 118
- IP filters 119
- Default filters 120
- To define a filter 120
- Action Direction 121
- Source /Destination 121
- Location 121
- ProtocolAddress 121
- 122 122
- IP filtering examples 123
- 124 124
- Blocking web surfing 125
- 126 126
- Making a V.120 connection 127
- 128 128
- SecurID support 129
- 130 130
- Other Configuration Tools 131
- Configuration options 132
- Web interface 133
- TFTP interface 133
- 134 134
- DTMF interface 135
- Command line interface (CLI) 136
- 137 137
- About configuration context 138
- Connection profiles 138
- Default profiles 138
- Command line reference 138
- Loading firmware with the CLI 138
- 139 139
- TCP/IP Configuration 140
- Installing TCP/IP 141
- Configuring TCP/IP 141
- 142 142
- 143 143
- 144 144
- Configuring TCP/IP on an iMac 145
- Technical Information 146
- 147 147
- E1, E2, E3, E4 148
- 149 149
- 150 150
- Termination 151
- Command Line Reference 152
- Notational Conventions 153
- Commands 154
- Callback 155
- Call screening 156
- Call thresholds 157
- 158 158
- 159 159
- Ethernet 160
- 161 161
- 162 162
- 164 164
- 165 165
- 166 166
- IP routing 167
- IP various 167
- 168 168
- 169 169
- 170 170
- 171 171
- ISDN Access Time 172
- Logging and Mail Trace 173
- 174 174
- SHOW MLPPP CONFIGURATION 175
- 176 176
- 177 177
- 178 178
- 179 179
- 180 180
- Profiles 181
- 182 182
- 183 183
- 184 184
- Time Protocol 185
- 186 186
- V.120 Scripting 187
- 188 188
- 189 189
- Regulatory Information 190
- Safety Status: TNV-1 191
- Power Consumption 191
Verwandte Produkte und Handbücher für Vernetzung Eicon Networks DIVA T/A ISDN Modem
Vernetzung Eicon Networks 1530 Betriebsanweisung
(162 Seiten)
(162 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.032 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern